5501

fokker t5 box

english                              Nederlandse lezers vinden hier het nederlandstalige artikel...

MODEL:  Fokker T.V  (late)  "luchtkruiser"

MANUFACTURER:  Valom

SCALE:  1/72

PRICE:   about  EUR 33,-

NEW MODEL:  yes, March 2016

The Fokker T.V was developed in the mid nineteen thirties as a "patrol cruiser for air superiority" with canon and machinegun armament and a small bomb bay. It was ordered by the Dutch air force "luchtvaart afdeeling" but only limited numbers were available when the war came in Holland in May 1940.

After several older models such as from KPL vacuform and the Czech resin kit more than 25 years ago (made available through the IPMS NL), there is finally a plastic injection molding model of the Fokker TV available. It's a short-run kit from Valom. The sturdy box contains three sprues of plastic, a bag with transparent parts, a bag of resin parts and a bag with decals. Also etched metal parts and a transparent film for the instrument panel are in the kit.

Sprue 1:

Sprue1A.

(sprue seen from other side...)

Sprue1B

Sprue 2:

Sprue2A

(seen from other side...)

Sprue2B

Sprue 3 :

Sprue3A

(and from other side...)

Sprue3B

Transparent parts, etched metal fret and resin parts in a small bag (with also gear bays, engines)

fokker t5 glass

fokker t5 fret

fokker t5 resin

The instructions contain the parts assembly and a layout printed in color. Valom has made clear progress here as for all construction phases colors are indicated with a table for 4 paint brands and Federal Standard "equivalents". Note that modellers who have the White Ensign Model (WEM) enamel colours of the Dutch air force ("luchtvaart afdeeling")  LVA can use these nicely for the LVA color scheme. The decals look fine but with only orange markings. The LVA tri-angles seem to have correct  10cm wide black edge (1.4 mm in 1/72 scale). White aircraft codes for 5 aircraft are included.

fokker t5 decals

The kit's parts are well made and crisp. Fuselage and wing halves are provided with fine engraved panel lines and a beautiful linen effect. The fuselage features an interior, though there is always room for super detailling. For example adding the engine throttles to the left of the pilot, the side console is already provided.

The structure for "Solothurn" cannon in the nose is provided as etched metal. So a bit flat as in reality these were tubes. But due to the complexity, it is understandable that Valom choose this solution. In order to fit the cannon barrell, you need to drill a hole in the nose glass, a risky task. But the aircraft also flew a lot without the cannon but usually than in a scheme with LVA roundels (and not the tri-angles; the roundels are not in this kit).

The pilot controls are also etched metal parts but look good once installed. The fuselage spine hatch is moulded close but if you want an open hatch, you will need to do some work.  The main wheel bays are resin parts as wel as the Bristol Pegasus engines and they look good. The propeller blades are all separate so merging them to get a couple of propellers is a bit painstaking. Also, the upper fuselage spine window looks a bit too flat. Each cowling consists of two halves and are neat, but lack the rear cooling doors. There is a recessed edge but no doors, making these of thin plastic card is recommended (SEE ADDENDUM BELOW...).

The engines were also supported by struts, these can be made of rod. The undercarriage looks good, the wheels have a flat surface.

Motorkap

The kit's instruction are unlogical, better follow this sequence:

- fuselage assembly

- assemble the wing halves with nacelles

- fit engine supports in the cowlings and fit the engine and cowling to nacelle

- attach the wing halves to the fuselage, some work needed with good alignment

- add rear empennage

- add glass work and mask all clear areas

- fill and sand as needed

- apply paint scheme

- complete the model

fokker t5 cockp.fokker t5 front

Nacelles and wing halves fit pretty well, do not forget the resin wheel bays.

MotorgondelA.

MotorgondelB

Valom has provided fuselage recesses to fit each wing half, some trimming is needed as the wing mating edge is a bit too thick. The horizontal stabilizer comes together better when ejection pin marks are sanded flat.

GeheelA.

GeheelB

It seems that this kit is much better than previous Valom kits. But still it is a short run kit, so always check fit and alignment. (in the past I made Valom kits and much work was needed for example to get a proper fit of the clear parts). This kit looks to fit good in the main areas and any smaller gaps can be closed with strip and putty.

More than 25 years ago I made the Czech resin Fokker T.V resin kit. I still had an unassembled kit and did a quick comparison:

- rear fuselage dome has a 2 - 3 mm bigger diameter

- engine nacelles are a few millimeters positioned more outboard

- stabilizer with a bigger taper-ratio.

- for the remainder: shapes and smaller parts look very similar.

As nowadays much more Fokker T.V information is available to anyone and looking at the Valom kit, I conclude that Valom did their home work. So this 1/72 scale kit is definitely recommended to Dutch Aviation modelling enthusiasts with some modelling experience. I hope to see many models built on modelling shows in the future.

REVIEWER:  Peter Booij

March 2016

References:

Frits Gerdessen and Luuk Boerman: Fokker T.V Luchtkruiser, Dutch Profile no 9, 2009

Hugo Hooftman, Fokker T.V en T.IX, Nederlandse Luchtvaartencyclopedie (rare book)


 

ADDENDUM  of March 25, 2016

(a) In the inbox review above of the Valom fokker T.V, I wrote that most probably the cooling gills of the engines were missing from the kit.

Well, that was correct. Erwin Stam of the Aviation Megastore contacted Valom and they confirmed the omission. Even better, VALOM will immediately produce a photo-etch correction set with the missing cooling gills. This correction set will be free for everybody who bought a Fokker T.V. As soon as the sets are ready, they will be send it to the shops who sold the kit. That’s what I call customer service from Valom. Well done!

 

Message April 8, 2016:   Photo-etch set with cooling gills available.

We got the message from Erwin Stam that he has received the photo-etch set with cooling gills and modified pages of the instructions. Each customer can contact the Aviation Megastore to obtain a set and the page of the instructions. Modellers who bought the kit at another store can inquire there. The new batch of T.V kits are already completed with the missing parts.

fokker tv add on

fokker tv cowling

(b) Furthermore, Erwin pointed me to a small error in the instructions:  it is not entirely clear whether the engine exhausts are located on the outside of the engine nacelles (lefthand- and righthand side) or only at the lefthand side of the nacelles. The answer came after consulting pictures:  the exhausts are located at the outside of the engine nacelles, as shown in the drawings of the colour schemes.

Peter Booij

 

Enthusiasts and historians can see more Fokker T.V information at our IPMS Nedmil Fokker T.V pages